Assembling a high-end gaming throne shouldn't require an engineering degree, yet the sheer weight and precision engineering of the Secretlab Titan Evo series catch many buyers off guard. If you've just unboxed your chair and want to get it set up without stripping threads or pinching your fingers, you're in the right place.
The Secretlab Titan Evo (often searched alongside the 2022 series and older iterations) weighs roughly 34 kilograms out of the box, making a methodical, step-by-step approach essential for a safe build. Let's dive straight into the tools, prep work, and precise mechanical sequence needed to assemble your chair correctly on the first try.
Before You Begin: Unboxing and Workspace Setup
Don't rip open the cardboard with a utility knife blindly; you risk slicing into the upholstery or magnetic side covers. Lay the large shipping box flat on its side if possible, or slice the tape along the top and lift the components out one by one.
Clear a spacious, flat area on a carpeted floor or large rug. Hardwood or tile can scratch the aluminum base or the chair's PU leather and SoftWeave fabric during assembly.
What Comes in the Box
- Aluminum wheelbase and five PU casters
- Class 4 heavy-duty hydraulic piston and telescopic cover
- Multi-tilt mechanism pre-mounted to the seat base or packed separately
- Seat base with 4D armrests pre-installed
- Backrest with integrated lumbar support tracks
- Magnetic side cover plates (left and right)
- Magnetic memory foam head pillow
- Allen wrench (hex key) and multi-head screwdriver tool
Step 1: Assemble the Wheelbase and Casters
Start from the ground up by building the foundation. Grab the ADC12 aluminum wheelbase and lay it flat with the socket holes facing upward.
Take the five PU-coated casters and push the stem of each caster firmly straight into the holes at the end of each wheelbase spoke. You shouldn't need a hammer; a firm, downward push with the palm of your hand will cause the snap-ring to click securely into place. If a caster feels loose, pull back slightly to test that the retention ring has seated inside the socket.
Next, take the hydraulic piston and drop it vertically into the exact center hole of the wheelbase. Slide the multi-section telescopic plastic cover down over the piston, with the wider end resting at the bottom against the base.
Step 2: Attach the Multi-Tilt Mechanism to the Seat Base
Flip the seat base upside down so the bottom mounting plate area is exposed. If your model came with the multi-tilt mechanism detached, align it with the four pre-drilled screw holes on the underside of the seat cushion.
Pay close attention to the directional arrow stamped onto the metal mechanism plate. The arrow pointing toward the front of the chair must face the front edge of the seat cushion.
Use the M8 screws and split washers provided in the hardware kit. Thread each screw in by hand first to avoid cross-threading the internal metal nuts welded into the seat base. Once all four are finger-tight, use the included Allen wrench to tighten them in a crisscross pattern until snug. Do not over-torque them with power tools, as excessive force can strip the internal threading.
Step 3: Mount the Seat Assembly onto the Piston
With the heavy mechanism now bolted securely to the bottom of the seat, lift the entire seat assembly over the wheelbase.
Align the central hole of the multi-tilt mechanism directly over the top spindle of the hydraulic piston. Lower the seat straight down onto the piston. Your body weight when you first sit down will lock the taper-fit securely, but giving it a firm push downward helps seat it initially.
Step 4: Secure the Backrest to the Seat Brackets
The backrest is heavy and awkward to hold alone, so prop yourself comfortably or have a second person steady the components for this phase.
Slide the lower metal brackets of the backrest into the steel channels protruding from the rear of the seat base. The brackets should slide smoothly on the inside of the hinges.
Secretlab equips these chairs with side wings and magnetic covers. Secure the backrest using the four M8 side screws (two on each side). Thread them partially into place on the left side, then the right side, before tightening any of them fully. This ensures the backrest aligns symmetrically without binding against the recline mechanism.
Step 5: Install the Magnetic Side Covers and Head Pillow
Once the main structural bolts are tightened, snap the magnetic side covers over the exposed metal hinges on both sides of the chair. The powerful rare-earth magnets will pull the covers straight into position with an audible click, concealing the hardware cleanly.
Finally, attach the magnetic memory foam head pillow to the top of the backrest. Because the Titan Evo uses a magnetic strap system rather than a traditional elastic band sliding over the top, you can slide the pillow up or down instantly to match your exact height.
For official warranty registration and safety guidelines, consult the Secretlab Support Hub.
Common Assembly Mistakes to Avoid
- Cross-threading screws: Never force a screw if it resists turning smoothly. Back it out and realign the metal bracket.
- Backward tilt mechanism: Mounting the bottom plate backward will prevent you from locking the tilt or adjusting tension properly. Always check the front-facing arrow.
- Forgetting washers: Always use the split washers included with the hardware bolts to prevent screws from vibrating loose over time.
Frequently Asked Questions
Do I need any external tools to assemble a Secretlab chair?
No. Secretlab includes a specialized multi-head tool and Allen wrench in the accessory box, containing everything required for the build.
How do I adjust the built-in lumbar support?
The Titan Evo features an integrated 4-way L-ADAPT lumbar system. Instead of an external pillow, use the two knobs on the sides of the backrest to adjust both the depth and height of the lumbar curve to fit your lower spine.
Can I assemble this chair by myself?
Yes, one person can easily assemble the chair in about 30 to 40 minutes. However, because the backrest and seat base have some weight, having a second person assist with holding the backrest steady during bolting makes the process much smoother.
What is the weight capacity of the Titan Evo model?
The Regular size supports users up to 290 pounds (130 kg) and heights up to 5'11" (180 cm), while the XL variant accommodates users up to 395 pounds (180 kg) and heights up to 6'9" (205 cm). Always verify your specific model specifications on the Secretlab Official Website.
